Quick Wood Lathe Chucks – Wood and Glue

During the thousands of years that we have been using them, various ways of holding work on the lathe have been developed. One such for faceplate work is the glue and paper joint but modern glues have made it even better.

Both the old style and the new start the same way. A piece of scrap wood is screwed to a faceplate and turned round and flat. Now a piece of wood suitable for a bowl or platter is selected. For consideration purposes, let us assume it is for a platter.

A piece is selected that is deep enough for securing to a faceplate with short screws. This is done to the top of the piece. First the outside is turned round and the bottom is turned flat. While the piece turns a pencil is used to make a ring the size of the scrap wood on the faceplate.

The old method of using the chuck involved gluing a piece of craft paper to the waste wood and then to the platter blank, carefully centering the chuck in the pencil lines. A clamp or weight was put on the assembly, making sure it did not shift, and it was left for at least eight hours to dry before being remounted on the lathe. Once the top was turned the chuck was removed by inserting a chisel at the paper line and splitting it, leaving paper on both chuck and platter. It remained to scrape and sand off the paper. While the system worked well, drawbacks to this method involved the long glue curing time and the inability to work with green wood because the old glues did not stick to wet wood.

The same hot glues the crafters use allow us to adopt the old method easily to dry wood for platters. In this case the paper is omitted and hot glue is applied to the waste block which is quickly centered on the pencil ring on the bottom. Hot glue is very strong with the stresses of turning but has little shear strength. This means that once the top is turned and the piece sanded, a chisel can be inserted at the glue line and a quick mallet rap will separate the waste and the platter. Remaining glue is easily cleaned up and the pencil ring sanded away.

Cyanoacrylate glues, sometimes referred to as super glues after a particular brand name, allow the same procedures for green wood. Again, they have excellent strength except for shear applications and can be separated with a mallet rap. If accelerator is applied to the piece and cyanoacrylate applied to the waste the work can be immediately mounted on the lathe as can dry wood with hot glue. In both cases the waiting time is inconsequential and there is no paper to scrape away.

Sometimes the old ways are the good ways. With a little innovation they can be even better and allow even greater enjoyment in the craft of woodturning.

Darrell Feltmate is a juried wood turner whose web site, Around the Woods, contains detailed information about wood turning for the novice or experienced turner as well as a collection of turnings for your viewing pleasure. You too can learn to turn wood, here is the place to start. Wondering what it looks like? There are many free videos on the site dealing with everything from sharpening to making a bowl.

About the Author

Wood Turning Projects Turning a Mini Birdhouse On The Lathe 1 OF 2

Woodturning: Getting Started Right with Alan Lacer This is another internationally awarded video from Alan Lacer. This unique video for the new woodturner–or anyone wishing to build a strong foundation–covers all the basics prior to actually turning. There is an extensive section covering woodturning tools: types, uses and sharpening. Alan shows you a variety of lathes, how to select a lathe, its operation, chucks and chucking, examples of turne…

PSI Woodworking Products TM32KL Keyless 1/2-Inch Drill Chuck with a 2 MT Mount $28.86 …

PSI Woodworking LCMINI2 Mini 5-Piece HSS Wood Lathe Chisel Turning Set $28.96 Ideal 5 piece wood lathe chisel set for small detailed turning projects on your mini lathe.Premium long lasting HSS blades with beautifully turned and stained hardwood handles and brass ferrulesIncludes:-1/4-inch roughing gouge, 1/8-inch spindle gouge,-1/4-inch round nose scraper, 3/32-inch parting tool,-1/4-inch skew chiselChisels are 10-1/2-inch in overall length with 4-inch bladesFantastic buy …

PSI Woodworking CSC3000C Barracuda Wood Lathe Key Chuck System $168.00 Get a powerful grip on your work with the PSI Woodworking CSC3000C Barracuda Wood Lathe Key Chuck System. The “T” handle chuck key enables you to use one hand to tighten the jaws. Suitable for Mini, Midi & Full sized lathes Comes in a 9-pc molded carrying case. Body: 4 lbs. 3.5″ dia….

Woodturning Shopmade Tools and Jigs DVD $33.95 Using the wood lathe and a drill press as primary machines, Alan Lacer takes you through the making a wide variety of shopmade tools and jigs. You will learn fundamentals of steel selection as well as some basic heat treating. From creating a number of tools, he will also show you how to make two different jigs useful in completing the base and bottom of bowls and vessels (reverse chucking). …

DVD Festival – How-to Wood Turning Library – 7 Titles on 10 Dvds $89.99 DVD How-To Wood Turning Festival with Ron Brown. This is a collection of 7 stand alone titles on 10 DVD’s providing over 11 hours of instruction for anyone wanting to learn to turn wooden items on a wood lathe. This set deals with mostly spindle projects. The DVD titles are: “I have a lathe. Now what?”, “Project Sampler – 7 Projects for the new turner.”, “Bottle Stoppers”, “Spinning Tops”, “Fancy…

Projects Along the Woodturning Trail $48.99 Another Telly Award video from Alan Lacer. This 2 DVD set provides an enormous amount of information for the new to even seasoned woodturner. The first DVD provides a review of sharpening, review of tool applications then jumps right into a series of skill building exercises. The second DVD takes you through examples of between center work, face-grain work and concludes with a project that in…

Wood turner’s Tool Roll By Peachtree Woodworking PW3332 $9.99 Store your lathe turning chisels, gouges, skews and more in this convenient Woodturner’s Tool Roll! Measuring 29″ x 19-1/2″ when laid out, the tool roll provides plenty of room for your lathe tools and more. The canvas roll has 14 pockets measuring 12″ deep and the pockets vary in width for different size tools. Two nylon web straps with buckles secure the tool roll after it is rolled up. The tool…

MSA Safety Works 817893 Adjustable Faceshield $15.99 Faceshield meets all applicable requirements of American National Standard Institute ANSI Z87.1-1989; This attractive faceshield is comfortable and functional. It features a high impact polycarbonate clear visor that is easily attached. The visor flips up, and stays put, when not in use. The ratchet suspension knob adjusts the size of the frame’s suspension to the user’s head, for a custom fit. A …

PS Wood 3 Back-Up Pad $21.00 3″ width with hook & loop surface; 1/4″ shaft…

Tags: lathe, tools, turning, woodturning, woodturning lathe, woodturning lathe accessories, woodturning lathe chucks, woodturning lathe reviews, woodturning lathe sale, woodworking

This entry was posted on Saturday, September 18th, 2010 at 11:38 pm and is filed under Uncategorized. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.